The term touchpad allows you to use your laptop without using a mouse. So, if you are encountering the laptop touchpad not working windows 10 issue then here in this article you can check the best ways of resolving the issue of Touchpad not working in Windows 10.

Why Does Touchpad Not Working in Windows 10?

In this article we have cover the most common ways to resolve a non-functioning Touchpad issue. However, if you cannot resolve your computer Touchpad issue then you can look the below given troubleshooting steps. We have explained the solutions that help you in resolving this error.

Here you can look at the reasons that why touchpad not working in Windows 10:

1: Operating System not responding.

2: FN key combination.

3: External Device and lot more.

How to Fix Touchpad not Working Problem?

When your computer touchpad stops working then no need to get panic as this issue can be resolved very easily. Here we have walk through some common troubleshooting steps to fix this issue. Keep Reading!

Solution 1 – Install the Latest Drivers:

It’s quite obvious that you will need drivers for Windows 10. Therefore, you need to check your manufacturer’s website for Windows 10 drivers. However, if there are no windows 10 drivers then there is a need to install them in compatibility mode.

Follow these given steps to install the Latest Drivers:

1: Firstly, you need to download the driver and then right-click the setup file.

2: Now, choose Properties and then go to Compatibility mode.

3: Next, you need to download the driver and then right click the setup file.

4: Again, choose Properties and then go to Compatibility tab.

5: Now, check “Run this program in Compatibility mode” and then choose Windows 10 from the list.

6: Finally, you can install the driver and see if still the problem persists or not and if not then look for the next step.

You must ensure that you will always need to look for the Windows updates time to time and keep your device updated and thus avoiding such issues.

Solution 2 – Enable Touchpad Setting:

One of the best ways to enable touchpad settings in Windows 10 is:

1: First, you need to connect the Windows search icon in the lower-left corner of the screen and then type touchpad.

2: Here the touchpad settings item will show up in the serach results list.

3: Click on it.

4: Now, you will be presented with a toggle button to turn the touchpad either on or off that means (Enabled or Disabled)

Solution 3 – Confirm Trackpad is connected properly:

Following has been listed some steps to confirm Trackpad is connected properly or not:

1: Firstly, you need to press the Windows key and then select the touchpad settings option in the search results.

2: In the touchpad Window, you need to make sure that the Touchpad ON/OFF toggle switch is set to ON.

3: Now, test the touchpad and see if it works or not.

Solution 4 – Remove and Reconnect the Touchpad:

In order to remove the Touchpad, you can perform these following steps:

1: First, click Start.

2: Now, type Device Manager into the search box.

3: In the Device Manager look for your mouse to Remove its Touchpad.

4: Now, right-click the touchpad entry and in the menu that pops up you need to click Uninstall Device.

5: Next, confirm your choice in the pop-up window.

To reconnect the Touchpad, do the following steps:

1: Press the Windows Key and then type Touchpad and press Enter or you can also press Windows Key + I to open settings and then choose Devices and then Touchpad.

2: In the touchpad settings Window, you need to click the Touchpad toggle to switch “On” its position.

Solution 5 – Turn On Bluetooth:

To turn on the Bluetooth, try these following steps:

1: Firstly, select the Start button and then select Settings>Devices>Bluetooth and other devices.

2: Now, select the Bluetooth switch to turn it On or Off as desired.

Solution 6 – Update your Windows:

Following has been listed some methods to update your Windows:

1: Firstly, you need to select the Start button and then select Settings>Update and Security>Windows Update.

2: Now, if you want to check for updates manually then you need to select Check for Updates.

3: Next, select “Advanced options” and then under Choose “How updates are installed select “Automatic”.

Solution 7 – Install the Device Drivers Manually:

To install the Device Drivers manually, look for these given steps:

1: Firstly, you need to visit the manufacturer’s website and then download the latest Windows driver.

2: Now, run the driver’s installation program.

3: Next, right-click the Start button and then choose Device Manager from the pop-up menu.

4: Click your Problematic device i.e listed in the Device Manager Window.

5: Now, you need to click Action from the device manager’s menu bar and then choose Add legacy Hardware from the drop-down menu and this will install the device drivers manually.

Solution 8 – Update Device Drivers:

To Update Device Drivers you need to follow these steps:

1: In the search box on the taskbar, you need to enter Device Manager.

2: Now, select Device Manager and then select a category to see names of devices and then right-click the one that you would like to update and select Update Drivers.

3: Next, search automatically for updated driver software.

4: Now, select Update Driver.

Solution 9 – Rollback to Older Driver:

Follow these steps to rollback to older driver:

1: Open Device Manager.

2: Now, Right click on Start and select Device Manager.

3: Next, expand Touchpad.

4: Now, double-click on your display device.

5: Select the Driver Tab.

6: Now, click Roll Back Driver to restore.

Solution 10 – Restart your Windows 10 Device:

To restart your Windows 10 device, try these following steps:

1: Press and hold the power button of your computer approximately 5 seconds.

2: Now, it will display with 3 options:

• Restart or Reboot
• Shutdown
• Sleep

3: You need to click on the Restart option and the computer will start restarted.

Solution 11 – Enable ETD Service:

The term ETD stands for Enterprise Threat Detection. In your Windows 10 you can enable it by the following methods:

1: Firstly, you need to press CTRL+ALT+DEL to open Task Manager and then go to the Services tab.

2: Now, you need to find ETD service and then Start it.

3: Next, you can restart your computer to see if the issue has been resolved or not and if not then continue with the next step.

Solution 12 – Enable ELAN:

Here has been defined few steps to enable ELAN:

1: First you need to click Start Button, Then select Settings form side bar.

2: Now, click Devices.

3: Next, you need to click Touchpad and then click Additional mouse options.

4: Move to the right option and the option could be Touchpad and also make sure that your touchpad is enabled.

Solution 13 – Set Touchpad to No delay:

Refer these given steps to follow:

1: Firstly, move to Settings>Devices>Mouse and touchpad>Additional mouse Options.

2: Now, you need to move to the Touchpad Tab.

3: Next, click Settings.

4: Go to the Advanced Tab.

5: Now, you can move to Check Threshold slider to min.

Solution 14 – Run SFC Scan:

Following has been listed some steps of how you can run SFC scan:

1: Firstly, you need to Search, type cmd and then open the Command Prompt as Administrator.

2: Now, you need to type the following command and then press Enter

• sfc/scannow

3: Now, you need to wait for the process to finish.

4: Restart your computer.

Solution 15 – Change Power Management Options:

One of the most essential features for every Laptop is Power Management. However, saving power can sometime become the cause for disabling some vital functions of your machine. It can also be possible that Power management machine settings help in preventing the touchpad from working.

1: Firstly, you need to search, type Device Manager and then open Device Manager.

2: Now, scroll down and then find your touchpad from the list of devices.

3: Next, right-click on Touchpad and then go to properties.

4: Now, head over to the Power Management tab.

5: Next, you need to uncheck the Allow the computer to turn off this device to save power option.

6: Restart your PC.

Solution 16 – Use Hardware Troubleshooter:

You can make use of Hardware Troubleshooter with the help of these following steps:

1: First, you need to go to settings.

2: Now, move towards to Update and Security>Troubleshoot.

3: Next, you need to click Hardware and Devices and then click and Run the Troubleshooter.

4: Wait for the process to finish.

5: Restart your computer.

Solution 17: Disconnect other USB Device:

 There also might be some chances that external USB device interferes with the touchpad. Thus, if none of the previous solution works then you need to try disconnecting all USB peripherals and then check if the touchpad works again or not.

Frequently Asked Questions:

 Q1: How you can fix touchpad when typing is not working?

 Ans: To fix touchpad issues you can follow these steps:

1: Open Control Panel.

2: Now, click on Hardware and sound.

3: Next click on Mouse.

4: Click on Clickpad.

5: Go to Settings and to the right of the White box.

6: Move to the Advanced Tab.

7: Now, turn down to palm tracking to minimum.

Q2: How you can fix Touchpad on Windows 10?

 Ans: In order to fix Touchpad on Windows 10 do the following steps:

1: First, you need to confirm that the trackpad is connected properly.

2: Now, remove and then reconnect the Touchpad.

3: Next, you need to check the Touchpad’s battery.

4: Turn on the Bluetooth.

5: Restart windows 10 device.

6: Next, you need to enable Touchpad in Settings.

7: Check for Windows 10 update.

8: Update Device Drivers.

 Q3: How you can diagnose touchpad problems?

 Ans: Here has been defined some of the best ways to diagnose touchpad problems:

1: First, clean off the toucpad.

2: Secondly, you need to disable the touchpad lock.

3: Check your touchpad settings.

4: Update your touchpad drivers.

5: You need to update your computer hardware and BIOS.

6: Un-install and then re-install your touchpad’s driver.

7: So, these are things that you will need.

Q4: What are the steps for enabling Synaptics in Windows 10?

Ans: Refer these following steps to enabling Synaptics in Windows 10:

1: Firstly, you need to open Start>Settings.

2: Now, select Devices.

3: Next, click on mouse and touchpad in the left hand bar.

4: Scroll to the bottom of the window.

5: Click on Additional Mouse options.

6: Select the Touchpad tab.

7: Now, click the settings button.

Q5: How you can re-install Synaptics touchpad driver?

Ans: You can follow these steps to reinstall Synaptics touchpad driver:

1: Firstly, you need to log on to the computer as a computer Administrator access.

2: Now, click Start and then click Control Panel.

3: Next, you need to click Performance and Maintenance.

4: Click System.

5: Select the hardware tab and then Click Device Manager.

6: Now, double click Mice and other Pointing devices.

7: Next, double click a displayed pointing device.

Q6: How you can update touchscreen Driver?

Ans: Follow the steps to update Touchscreen driver:

1: First, you need to select the Start button>All programs>Windows Update

2: Next, you need to select and check for updates.

3: If you find that there are any important updates then you need to select the link to view available updates.

4: Now, select Install updates and you might be asked for an admin password to confirm your choice.

Final Words

In this article we have cover all the important methods that help in resolving the issue of fix touchpad in Windows 10. You can follow these steps one by one and determine which step is going to help in fixing this issue.

However, if this won’t help then you can contact our experienced team of technicians who help you in solving this problem. Moreover, you can connect with us via chat and we assure you that we will be able to solve your problem within a specific amount of time.

Also, we are available all time so you can feel free to contact us and get relief from all printer related problems. Our experienced team provide you the hassle-free solutions for solving printer related problems. So, get in touch with us today and resolve all printer issues within a couple of time. If you like the article then you can comment us in the given comment section. Else, if you have any queries, then tell us.